Back to Blog
How-to Guides 2026-11-16 Leatherman 0 views

Two-Screw Pocket Clip: Tightening, Fit and Carry Tips

Two-Screw Pocket Clip: Tightening, Fit and Carry Tips

Learn how to install and tighten the Leatherman Two-Screw Pocket Clip, check fit, and carry your multi-tool securely with practical tips.

Start with the right clip and screws

The Leatherman Two-Screw Pocket Clip is designed to keep your multi-tool close and easy to grab. It includes two T6 screws for simple installation, so you can upgrade or replace your everyday carry setup without extra hardware. Before you begin, confirm you have the clip, the two T6 screws, and a T6 driver or bit that fits your multi-tool.

This guide focuses on installing and adjusting that specific clip. If you are unsure whether your tool accepts a two-screw clip, check your model’s compatibility first—fit varies across Leatherman models, and the supplied information for this clip does not list specific compatible tools.

What you get

  • Two-Screw Pocket Clip: Includes two T6 screws for simple installation. These are the fasteners you will use to secure the clip; having them on hand means you can install or re-tighten without sourcing separate screws.
    Two-Screw Pocket Clip
    Two-Screw Pocket Clip
  • Two-Screw Pocket Clip: Designed for a secure fit and clean look, it’s perfect for upgrading or replacing your everyday carry setup. This tells you the clip is intended to sit securely and look tidy—useful benchmarks when you check your installation.

How to install the Two-Screw Pocket Clip

  1. 1. Prepare your tool and driver: Set your multi-tool on a clean, flat surface. Have the Two-Screw Pocket Clip, the two included T6 screws, and a T6 driver ready. A driver that fits properly reduces the risk of stripping the screw heads.
  2. 2. Align the clip with the mounting holes: Position the clip over the corresponding screw holes on your multi-tool. The clip is shaped for a clean look, so it should sit flush against the handle when aligned correctly.
  3. 3. Start both screws by hand: Thread each T6 screw into its hole a few turns by hand before tightening with the driver. This helps avoid cross-threading and ensures the clip is seated evenly.
  4. 4. Tighten evenly: Use the T6 driver to tighten both screws alternately—a little on one, then the other—until the clip feels secure. Do not overtighten; the goal is a snug fit that holds the clip firmly without crushing it against the tool.
  5. 5. Check the fit: With the clip installed, slide your multi-tool into a pocket or onto a belt loop (if applicable) to test retention. The clip should grip without being difficult to slide on, and it should not wobble. If it moves, tighten each screw a quarter turn and recheck.

Tightening tips for a secure hold

If your clip feels loose over time, re-tighten the two T6 screws. Use a driver that matches the screw head precisely; a poor fit can damage the screws. Tighten in small increments, alternating between the two screws so the clip stays level. Avoid using thread-locking compound unless the manufacturer recommends it—the supplied information does not mention it, and some compounds can make future removal difficult.

Because the clip is designed for a secure fit, a properly tightened clip should hold your multi-tool without letting it swing freely. If tightening does not solve a loose clip, inspect the screws and the mounting holes for wear or damage before continuing to crank down.

Checking Leatherman pocket clip fit

Fit is about more than screw tightness. After installation, check that the clip’s bend clears the tool’s handle and that the clip opening is wide enough for your pocket or belt. The Two-Screw Pocket Clip is intended for a clean look, so it should not protrude awkwardly or interfere with opening and closing the tool.

The supplied information does not specify which Leatherman models accept this clip, so the safest approach is to compare the screw hole spacing on your tool with the clip’s mounting points before installation. If the holes do not line up, the clip is not the right fit for that model.

Pocket clip carry tips for daily use

  • Choose a pocket that suits the clip: Clip your multi-tool to a pocket where it sits comfortably and does not catch on other items. The clip keeps the tool close and easy to grab, but a crowded pocket can make it harder to draw.
  • Check retention regularly: Make it a habit to feel the clip’s tension when you put the tool away. If it starts to feel loose, tighten the T6 screws as described above.
  • Keep the clip clean: Lint and grit can build up under the clip. Wipe it occasionally with a dry cloth to help maintain a secure fit and smooth operation.
  • Avoid overloading the clip: The clip is designed to hold the multi-tool itself. Hanging extra items from it can bend the clip or loosen the screws.

When to replace or adjust your clip

If the clip bends out of shape or the screws no longer hold tight despite careful tightening, replacement may be the simplest fix. The Two-Screw Pocket Clip is available in Black, and its simple two-screw installation makes swapping it straightforward. Before replacing, double-check that your tool’s mounting holes are intact; a stripped hole will not hold any clip securely.

For minor adjustments, such as tightening or slight repositioning, the included T6 screws give you the hardware you need. If you frequently adjust your clip, consider keeping a T6 driver with your gear so you can tighten on the go.

Product details at a glance

  • Two-Screw Pocket Clip: Available in Black. A single color option keeps the choice simple and matches most multi-tool finishes.
  • Two-Screw Pocket Clip: Keep your multi-tool close and easy to grab with this sleek, durable pocket clip. This summarizes the clip’s purpose: convenient, quick access for your everyday carry.

Related Articles

Customer Service
Home
Products
Cart
Profile